Indirect water heaters are designed for domestic hot water systems in a country house.
The wall-mounted tank is designed for accumulating hot water from various heat sources. The PW series tank improves the flexibility of the DHW system, allowing you to store a constant volume of hot water, use DHW recirculation to increase the comfort of use. And the ability to connect an electric heater to the 1 1/2″ female threaded hole at the bottom of the tank makes the tank more versatile.
Rated volume:
157-211 l
Height:
980-1250 mm
Diameter:
505 mm
Performance:
543-1050 l/h
Heat exchanger area:
0,8 - 1 m2
Capacity of heating element:
from 2 to 6 kW
— Tank allows flush-mounting of a recirculating pump, electric heating element, drain valve, antiflash valve and anodic protection. All these components can be hidden in the product body.
— 2 types of anodic protection to choose from — magnesium anode (5-year warranty) or active titanium anode (10-year warranty)
— 2 types of heating elements to choose from — wet heating element with a capacity of 2, 3 or 6 kW or dry heating element with a capacity of 2.4 kW (available from 01.01.2022). By doing so, the tank allows the Customer to use a wet heating element first and then, if necessary, replace it with a dry heating element, due to the universal design of flange connection at the tank bottom.
— Heat exchanger capacity ranges from 20 to 35 kW.
— Tank is equipped with an inspection flange at the top.
— Tank design makes it possible to push the tank against the wall or in the corner. The tank can also be piped from the left, right or top. This is due to availability of breaking off elements in the product body.
— Average thickness of the rigid polyurethane foam insulation is 80-85 mm — A class according to ErP.
— Enamel — glass-ceramic with ultra-high soft water resistance.
— Tank drain port is located on the front side under the glass blind panel below the heating element level. This enables easy replacement of the heating element if necessary.
— Sleeve for water heater sensor mounting has an inner diameter of approx. 14 mm and is designed to accommodate a sensor of any manufacturer. Special design of this sleeve, which is sliding throughout the tank body height, allows for maximum adjustment of the water heater loading efficiency with heat from the boiler.
— Cold water makeup and recirculation pipes are interchangeable, so can be swapped for easier installation and piping.
— Water heater face is tempered break-resistant glass painted in a color of the body.
— Adjustable support feet allow for tank mounting on any surface.
!!!200 and 300 liter tanks are not top-connected but side-connected!!!
Rated volume:
150, 200, 300 l
Height:
1140, 1350, 1700 mm
Heat exchanger capacity:
35, 35, 53 kW
Performance:
over 1000 l/h, over 1000 l/h, over 1500 l/h
Heat exchanger area:
1.1, 1.1, 1.6 m2
Temperature hot water supply:
80 degrees
Possibility of heating element installation
Length of heating element:
up to 500 mm
Connection diameter:
1 1/2'' or flange
Capacity of heating element:
2 to 6 kW
Performance of heating element:
30 to 150 liters per hour
Heating speed:
9.5 min, 12.5 min, 12.5 min
Heating temperature:
maximum 80 degrees
The tank is designed to accumulate hot water from various heat sources. The ‘P’ series tank improves the hot water supply system flexibility, allowing you to accumulate a constant volume of hot water and use hot water supply recirculation to increase comfort of use. And the possibility of connecting an electric heater via a 2″ (for 750 and 1000 litre tanks) or 1 1/2″ (for up to and including 500 litre tanks) hole with internal thread in the bottom of the tank makes the tank more versatile.
Rated volume:
150-1000 L
Height:
980-2200 mm
Diameter:
505-795 mm
Performance:
543-2155 l/h
Heat exchanger area:
0,8-2,4 m2
Possibility of heating element installation
The tank is designed to accumulate hot water from various heat sources. The ‘P’ series tank improves the hot water supply system flexibility, allowing you to accumulate a constant volume of hot water and use hot water supply recirculation to increase comfort of use. And the possibility of connecting an electric heater via a 2″ (for 750 and 1000 litre tanks) or 1 1/2″ (for up to and including 500 litre tanks) hole with internal thread in the bottom of the tank makes the tank more versatile.
Rated volume:
200-1000 l
Height:
1250-2200 mm
Diameter:
505-795 mm
Performance:
691-2155 l/h, 1092-2745 l/h
Heat exchanger area:
1-2,4 m2, 0,8-1,2 m2
Possibility of heating element installation
The tank is designed to accumulate hot water from various sources: – The tank is designed to accumulate hot water from various sources.
Rated volume:
150 - 2000 l
Height:
945 - 2100 mm
Diameter:
630 - 1350 mm
Performance:
от 522 до 2434 l/h
Heat exchanger area:
1,3 m2 до 5,8 m2
Polyester thermal :
70 mm thick (360°)
Possibility of heating element installation
Scope of use: accumulation and storage of hot sanitary water from a thermal pump or high-capacity boilers.
Rated volume:
300 - 2000 l
Height:
1570 - 2100 mm
Diameter:
630 - 1350 mm
Performance:
510-1750 l/h
Heat exchanger area:
3,2 m2 до 11 m2
Polyester thermal :
70 mm thick (360°)
Possibility of heating element installation
Scope of use: accumulation and storage of hot sanitary water.
Rated volume:
150 - 2000 l
Height:
945 - 2100 mm
Diameter:
630 - 1350 mm
Performance:
629-2434 l/h
Heat exchanger area:
1,58-5,8 m2, 0,86-3,8 m2
Polyester thermal :
70 mm thick (360°)
Possibility of heating element installation
